E20-260 : Specialist - Implementation Engineer, VPLEX Exam

E20-260 Dumps
E20-260 Braindumps E20-260 Real Questions E20-260 Practice Test
E20-260 Actual Questions
killexams.com DELL-EMC E20-260
Specialist - Implementation Engineer, VPLEX
https://killexams.com/pass4sure/exam-detail/E20-260
You have created a Distributed Device in a VPLEX Metro system. Which VPLEX Object can be placed in a Storage View for Cluster-1?
A. DD_8_3_vol
B. DD_8_32012Nov26_183659 C. Symm0841_03A7
D. extent_Symm0841_03A7_1
Answer: A
QUESTION: 201
Refer to the exhibit.
The customer deleted ext_2 on a 20 GB LUN in order to make an extent of 10 GB. Why is the customer unable to create a 10 GB extent?
1. Chunks of the storage need to be contiguous.
2. Storage array must be re-discovered.
3. ext_2 cannot be deleted.
4. The defrag property is set to false.
Answer: A
Reference the message type shown at point "1". What type of response will be sent back to the SNMP management server from the SNMP Agent?
1. A poll response containing requested data
2. A trap response containing requested data
3. A poll response that initiates a trap response
4. A trap response containing all MIB data
Answer: A
QUESTION: 203
Refer to the exhibit.
During a short power disruption to cluster 2, director-2-1-A failed. Power was restored after 5 minutes. In examining the output of the vault status command, you
1. The power disruption affected a single director only.
2. There was no power disruption at cluster-1
3. The power disruption did not affect all "A" directors.
4. The vaulting process runs on cluster-1
Answer: A
QUESTION: 204
Refer to the exhibit.
After a power disruption of 20 seconds in a VPLEX environment, the output of the "vault status" command shows no vaulting processes. Why did this occur?
1. The cache vaulting did not exceed the timer period.
2. It is the expected output, because the command "vault status" doesn't show information on cache process at all.
3. Cache vaulting process has already completed.
4. Cache vaulting process is still running in background and it is not shown until completed.
Answer: A
QUESTION: 205
Refer to the exhibit.
You have created a Distributed Device in a VPLEX Metro. You want to confirm you have chosen the correct volumes before performing a device mobility job within cluster-2. Which object will be the source for this operation?
A. DD_8_32012Nov26_183659
B. extent_Symm0841_03A7_1 C. Symm0841_03A7
D. DD_7_3
Answer: A
QUESTION: 206
Refer to the exhibit.
The customer has not followed EMC best practices when cabling their VS2 VPLEX engine. What action would you recommend to fix this issue?
1. Swap ports 00 with ports 01 of both director A and director B.
2. Swap port 02 with port 03 of both director A and director B.
3. Add two more additional fabrics and place each director in its own fabric.
4. Separate all FE and BE ports into their own fabric.
Answer: A
QUESTION: 207
How many management Ethernet connections exist between the management server and the engines?
1. 2
2. 4
3. 6
4. 8
Answer: A
QUESTION: 208
What is an EMC best practice for fault tolerance when zoning a VPLEX Metro together over Fibre Channel for successful communication between the sites?
1. Zone each WAN-COM port to all WAN-COM ports in the other fabric.
2. Zone all WAN-COM ports to each other in both SAN fabrics within a single zone.
3. Zone each WAN-COM port to all WAN-COM ports in the other fabric.
Zone one Local-COM port to all WAN-COM ports in the other fabric for VPLEX Witness.
4. Zone all WAN-COM ports to each other in both SAN fabrics within a single zone. Zone one Local-COM port to all WAN-COM ports in the other fabric for VPLEX Witness.
Answer: A
QUESTION: 209
When should front-end ports be enabled during a VPLEX installation?
1. After creating the meta-volumes and backup
2. Before creating the meta-volumes and backup
3. Before launching the VPLEX EZ-Setup Wizard
4. After exposing storage to the hosts
Answer: A
QUESTION: 210
An EMC customer wants to add a mirror to a VPLEX Local RAID 0 device. Which RAID type is created after the device attach-mirror command is issued?
1. RAID 1
2. RAID 0
3. RAID S
4. RAID C
Answer: A

User: Rodina***** If you are looking for a valid E20-260 practice test to prepare for the exam, look no further than Killexams.com. Their superb exam simulator provided me with high-quality study materials, guiding me through every element of the exam and supplying the best questions and answers I have ever seen. The test courses were also incredibly helpful.

User: Ammar***** To prepare for the e20-260 exam certification, I used Killexams.com questions and answers. Everything was brilliantly organized, and I found it particularly useful for topics like data gathering and design in the e20-260 exam. I answered all the questions and scored 89 marks, and it took me nearly an hour and 20 minutes. A big thanks to Killexams.com for their excellent material.

User: Sofya***** Without killexams.com’s testprep package, I would have struggled with the E20-260 exam’s vast range of subjects. Their comprehensive guidance ensured I missed no critical information, leading to a confident pass. I highly recommend their trusted resources to anyone preparing for IT certifications.

User: Ruslan***** As a busy IT professional, maintaining certification readiness is tough. Killexams.com’s structured practice tests allowed me to efficiently prepare for e20-260 despite my hectic schedule.

User: Nettie***** I am now e20-260 certified, thanks to the excellent practice tests and exam preparation resources from killexams.com. The authentic questions and reliable simulator made my preparation thorough and effective. I used their materials last year and found them equally impressive this time, making killexams.com my go-to for exam prep.

---