150-820 : Brocade Certified Ethernet Fabric Professional 2015 Exam

150-820 Dumps
150-820 Braindumps
150-820 Real Questions
150-820 Practice Test
150-820 dumps free



Brocade
150-820
Brocade Certified Ethernet Fabric Professional 2015
http://killexams.com/pass4sure/exam-detail/150-820
QUESTION 170
Exhibit:
sw0(conf-if-te-0/5)# channel-group 100 mode active type standard %%Error: A switchport or a router port cannot be aggregated Exhibit:
Referring to the exhibit, what is the cause of the error when applying a port channel to an interface?
A. A routing protocol is configured in the port channel.
B. Access mode is not supported with link aggregation.
C. Switchport is configured in the port channel.
D. Switchport is configured on the interface.
Correct Answer: D
QUESTION 171
Exhibit:
sw0# show cee maps
CEE Map 'default'
Precedence: 1
Remap Fabric-Priority to Priority 0
Remap Lossless-Priority to Priority 0
Priority Group Table
1: Weight 25, PFC Enabled, BW% 25
2: Weight 60, PFC Disabled, BW% 60
3: Weight 15, PFC Disabled, BW% 15
15.0: PFC Disabled
15.1: PFC Disabled
15.2: PFC Disabled
15.3: PFC Disabled
15.4: PFC Disabled
15.5: PFC Disabled
15.6: PFC Disabled
15.7: PFC Disabled
Priority Table
CoS: 0 1 2 3 4 5 6 7
----------------------------------------
PGID: 2 3 2 1 2 2 2 15.0
Exhibit:
Referring to the exhibit, which two statements are true? (Choose two.)
A. CoS 1 is lossless.
B. CoS 3 is lossless.
C. CoS 1 has a 15% bandwidth guarantee.
D. CoS 3 has a 15% bandwidth guarantee.
Correct Answer: BC
QUESTION 172
Referring to the exhibit, you have configured VRRP-E in your Brocade VCS Fabric on two switches connected to your intranet. You want to prevent
unnecessary traffic on the ISL links.


Which feature would you use to accomplish this task?
A. track ports
B. equal cost multi-path
C. preempt mode
D. short-path forwarding
Correct Answer: D
QUESTION 173
Referring to the exhibit, which statement is correct?


A. VF5020 configuration is invalid because RBridge 2, Port 1 is configured for VLAN 10, while all other ports are configured for VLAN 20.
B. The configuration for RBridge 2, Port 1 is invalid because multiple Virtual Fabrics are configured for an overlapping VLAN on the same physical port.
C. The configuration on Port 2 on all RBridges is invalid because service and transport VFs are mutually exclusive on the same physical port.
D. The configuration on Port 1 on all RBridges is invalid because multiple Virtual Fabrics are configured on the same physical port using different VLAN
IDs.
Correct Answer: B
QUESTION 174
Router 2 has failed. You want to know what will happen when Host 3 tries to send traffic to the Internet.


Referring to the exhibit, which statement is correct?
A. Host 3 can send traffic to the Internet through Router 1.
B. Host 3 cannot send traffic because the ISL link is down.
C. Host 3 can send traffic but the priority set on Router 1 will drop some traffic.
D. Host 3 cannot send traffic because Router 1 was not tracking the correct port.
Correct Answer: A
QUESTION 175
You are configuring OSPF in a Brocade VCS Fabric. The implementation will integrate with an existing OSPF network. The fabric is in logical chassis
mode.


Referring to the exhibit, which three actions are correct? (Choose three.)
A. Enable OSPF at the RBridge level.
B. Enable OSPF globally in the fabric.
C. Enable OSPF on interface Ve 10.
D. Enable OSPF on interface 131/2/15.
E. Enable OSPF on interface 131/2/22.
Correct Answer: ACD
QUESTION 176
You have formed a Brocade VCS fabric with four switches.


Referring to the exhibit, which Brocade VDX would be the principal RBridge?
A. RB1
B. RB2
C. RB3
D. RB4
Correct Answer: D
QUESTION 177
You added a new Brocade VDX 6740 to an existing Brocade VCS Fabric in your data center. You connected the VDX 6740 to ports 3/0/11 and 3/0/12
on the existing fabric. After the switch boots, you realize it does not join the fabric. You examine the ISL status on the fabric as shown in the exhibit.
sw0(conf-if-te-3/0/19)# do sh fabric islport
Name: sw0
Type: 95.2
State: Online
Role: Fabric Principal
VCS Id: 1
Config Mode:Distributed
Rbridge-id: 3
WWN: 10:00:00:05:33:46:71:61
FCF MAC: 00:05:33:46:71:61
Index Interface State Operational State
=================================================================== 0 Te 3/0/1 Down
1 Te 3/0/2 Down
2 Te 3/0/3 Down
3 Te 3/0/4 Down
4 Te 3/0/5 Down
5 Te 3/0/6 Down
6 Te 3/0/7 Down
7 Te 3/0/8 Up ISL 10:00:00:05:33:5c:e1:5a "sw0" (downstream)(Trunk Primary) 8 Te 3/0/9 Up ISL (Trunk port, Primary is 3/0/8 )
9 Te 3/0/10 Down
10 Te 3/0/11 Up ISL (Trunk port, Primary is 3/0/12 ) 11 Te 3/0/12 Up ISL segmented,(ESC mismatch, Config Mode)(Trunk Primary) 12 Te 3/0/13 Down
13 Te 3/0/14 Down
14 Te 3/0/15 Down
15 Te 3/0/16 Down
16 Te 3/0/17 Down
17 Te 3/0/18 Down
18 Te 3/0/19 Down
19 Te 3/0/20 Down
20 Te 3/0/21 Down
21 Te 3/0/22 Down
22 Te 3/0/23 Down
23 Te 3/0/24 Down
What is causing the problem?
A. The new switch VCSID is incorrect.
B. The new switch has an overlapping RBridge ID.
C. The new switch does not have a VCS Fabric license.
D. The new switch is not configured for logical chassis.
Correct Answer: D
QUESTION 178
Exhibit:
switch# show ip route

Destination Gateway Port Cost Type Uptime
1 0.0.0.0/0 10.24.64.1 mgmt 1 1/1 S 8m24s
2 1.1.1.0/24 10.1.1.10 Ve 10 1/1 S+ 3m11s
3 1.1.2.0/24 DIRECT Ve 12 0/0 D 3m11s
4 10.24.64.0/20 DIRECT mgmt 1 0/0 D 8m28s
Exhibit:
Referring to the exhibit, which statement is true?
A. The route to 1.1.1.0/24 is a backup, and only active if the default route goes down.
B. The 1.1.1.0/24 subnet is in a different VRF.
C. The default route was dynamically learned.
D. The 1.1.2.0/24 route was dynamically learned.
Correct Answer: B
QUESTION 179
You have formed a Brocade VCS Fabric. The fabric has four RBridges.
sw11# show vcs
Config Mode : Local-Only
VCS ID : 101
Total Number of Nodes : 4
Rbridge-Id WWN Management IP Status HostName
-------------------------------------------------------------------------------- 11 10:00:00:05:33:55:64:B3* 10.255.245.7 Online "VDX11" 12 >10:00:00:05:33:55:5F:73
10.255.245.8 Online "VDX12" 13 10:00:00:05:33:91:4A:0B 10.255.245.29 Online "VDX13" 21 10:00:00:05:33:55:5D:F3 10.255.245.12 Online "VDX21"
Referring to the exhibit, which RBridge ID shown in the output is the principal RBridge?
A. RBridge 11
B. RBridge 12
C. RBridge 13
D. RBridge 21
Correct Answer: B
QUESTION 180
You are designing a single Brocade VCS Fabric for your data center network. Your MLX core routers are stand-alone. You want to use vLAG
connectivity for devices. All link groups need to form single vLAGs.
Referring to the exhibit, which link group will accomplish this?
A. link group A
B. link group B
C. link group C
D. link group D
Correct Answer: D
QUESTION 181
A company has a Fibre Channel (FC) array in which they would like to connect to their data center servers using their existing Brocade VCS Fabric
running NOS v4.1.0.

Referring to the exhibit, which two scenarios would accomplish this goal? (Choose two.)
A. A
B. B
C. C
D. D
Correct Answer: BC
QUESTION 182
Exhibit:
RB10# show mac-address-table port-profile
VlanId Mac-address Type State AMPP Ports
100 0050.65bf.0001 Dynamic Active Profiled (T) 2/0/1 100 0050.65bf.0002 Dynamic Active Profiled (UC) 2/0/1
Exhibit:
Referring to the exhibit, what would you determine about this interface?
A. Multiple VLANs are present on the interface.
B. A single MAC address is learned on the interface.
C. There is a conflict on the interface.
D. The interface is unshielded copper.
Correct Answer: C
For More exams visit https://killexams.com/vendors-exam-list




Kill your exam at First Attempt....Guaranteed!

User: Katherine***** Killexams.com has been the most outstanding mentor I could have asked for. Their teaching methodology is unparalleled, and within just two weeks, I achieved remarkable results in the 150-820 exam. My success in this field is largely due to their expertise.

User: Verochka***** I was able to pass the 150-820 exam on my first try with a 98% score, all thanks to Killexams. The case studies and study materials they provided were very helpful. The only thing I wish for is that the timer could run during the exercise test, so I could practice my pacing better.

User: Orlyn***** Joining killexams.com was a game-changer, elevating me to the top ranks among my peers for the 150-820 exam. Their practice tests and exam simulator were valid, up-to-date, and highly effective, providing clear explanations and realistic questions. I passed with an impressive score and am thrilled to recommend killexams.com’s resources to other students. Their support deserves all the praise.

User: Rusell***** Killexams.com played a pivotal role in my journey to earning the 150-820 associate certification. Their exam simulator was remarkably accurate, closely mirroring the actual exam environment. The practice tests were clear, concise, and easy to follow, which made studying the topics straightforward. Although the exam itself was unpredictable, Killexams.com’s preparation materials ensured I was well-equipped, resulting in a satisfying outcome.

User: Savya***** I had delayed taking the 150-820 exam due to my busy schedule at work. But after discovering the questions and answers provided by Killexams.com, I felt motivated to take on the test. The material was supportive and helped me resolve my doubts about the 150-820 topic. I was extremely happy to pass the exam with an excellent score of 97%. Thank you, Killexams, for your incredible support.

---